DPCAV
GOPROHD HERO/HERO2 CAMERA CABLE (PRO SERIES), AUDIO & VIDEO
| Orange | Audio (mono) |
| White | Video |
| Red | Not Used |
| Black | Ground |
The overall cable length is 15-inches (380mm) long. It has a 2.5mm phone plug on one end and the other end has two plugs: a black Futaba style male plug for video and a red JR-Hitec receptacle (female) for audio., The wire color codes are as follows:, ,
This lightweight A/V (audio/video) cable is used to connect the ...DPCAV
GOPROHD HERO/HERO2 CAMERA CABLE (PRO-SERIES), VIDEO ONLY
| White | Video |
| Red | Not Used |
| Black | Ground |
The wire color codes are as follows:, ,
This lightweight video cable is used to connect the popular ...DPCAV
DELUXE A/V CABLE FOR TX9-500 / TX13-300 / TX13-1000 TRANSMITTERS, PRO-SERIES
| Orange | Audio input, connects to microphone or OSD |
| Red | +12VDC (from DC-IN) to power 12V microphone |
| Brown | Common Ground |
| White | Video from camera or OSD |
| Red | +12VDC (from DC-IN) to power 12V camera |
| Black | Common Ground |
| Red | +12VDC, to battery |
| Black | Common Ground, to battery |
Referring to the photo below, a summary of each connector is as follows:, , Polarity Guard:, Special circuit protects the video transmitter from reverse battery voltage., Video Tx:, This 4-pin cable plugs into the TX9-500, TX13-300, or TX13-1000 video transmitter., Audio-In:, Male style servo cable, goes to optional microphone or OSD Audio-out port., Video-In:, Female style servo cable, goes to video camera or OSD Video-Out port. EagleTree OSD applications will also need the, DC-IN:, JST (BEC) style female cable. Goes to the 12VDC battery that powers the video transmitter and camera.,
Upgrade your transmitter's bulky RCA cables with this custom wire ...DPCAV
CUSTOMIZED A/V CABLE FOR TX-5G8-600 TRANSMITTER, PRO SERIES
| Red | To battery |
| Black | To battery |
| Orange | Audio input, connects to microphone or OSD Audio-Out |
| Red | Voltage from DC-IN is sent here to power an optional microphone (available separately) |
| Brown | Common Ground |
| White | Video from camera or OSD |
| Red | The voltage from DC-IN is sent here to power the camera |
| Black | Common Ground |
Referring to the photo below, a summary of each connector is as follows:, , DC-IN:, JST (BEC) style female connector. Goes to the battery that powers the video transmitter and camera. The TX-5G8-600 transmitter will accept 7-25VDC, but the battery voltage you choose must be compatible with the video camera., Audio:, Male style servo cable, goes to optional microphone or OSD Audio-out port., Video-In:, Female style servo cable, goes to video camera or OSD Video-Out port. EagleTree OSD applications will also need the,
Upgrade your ImmersionRC TX-5G8-600 transmitter cable with this custom wire ...DPCAV
WIRELESS VIDEO TRANSMITTER & OSD, FPV DEAL
| Item A | EagleTree eLogger V4 with 100 Amp sensor. |
| Item B | USB cable for eLogger firmware updates. |
| Item C | Eagle Tree OSD Pro Video Expander module. |
| Item D | GPS extension cable for kits shipped before June-2010. |
| Item E | eLogger GPS-V4 Expander module. |
| Item F | Eagle Tree OSD Pro cable Kit. |
| Item H | DPC-420A 420 line CCD color camera. |
| Item I | DPC-420A/480A camera interconnect cable. |
| Item J | TX9-500 900MHz / 500mW transmitter. |
| Item K | Dipole Antenna, +3dBi omni-directional. |
| Item L | Deluxe A/V cable for TX9-500 transmitter. |
| Item M | Male-male video adapter cable, |
This wireless OSD system will transmit graphic data and voice announcements that report a variety of alarms and data, including: voltage, current, mAH, Watts, Home Arrow, Return to Home (RTH / RTL), RADAR, altitude, course (travel direction), ground speed, longitude, latitude, and navigation waypoints. You can expand this system even further by using the low cost eLogger accessories, such as these:Click Me!, Here's a screen shot that shows some of the information that can be shown (temperature and RPM data requires optional accessories):, , All the data parameters that are supported by the eLogger can be displayed on the video display. Here are some examples:, , Notice: Due to the 900MHz transmitter's high RF power, using it in the USA and other countries will require an amateur/ham radio license (some countries may forbid its use). It is your responsibility to ensure that its use meets the requirements of your government’s RF spectrum regulations. Do not purchase this product if you are unsure of the government requirements or are not able to comply with them., . We have other battery choices so that you can select the best one for your application. More choices:Click Me, (3) The 900MHz A/V receiver is not included, but we offer fully compatible models that work great with this special package. Please look here to purchase them:click here, The video format is available in NTSC or PAL. If you are unsure which to choose then please consult this list:TV Video Standards., ,
Ok, so you've decided that you need the EagleTree OSD ...DPCAV
ELOGGER BATTERY BACKUP HARNESS
| Instruction manual | Click Me! |
This 3-inch long harness cable allows you to power the eLogger from a separate 4.8V to 6.5V battery. There are three common situations where this cable is required:, (1) In installations where the primary battery or BEC frequently dips below approximately 4.5V, which causes a “reboot” of the eLogger system.,
(2) When using the GPS Expander on your eLogger with ...DPCAV
EAGLEEYES FPV STATION / ANTENNA TRACKING CONTROLLER
| Antenna Tracking | When used with the |
| Instruction Manual | Click Me! |
| Full details / Mfg's web site | Click Me! |
Features:, , Telemetry:, When coupled with the, Receiver Diversity:, When you connect two composite NTSC or PAL video receivers (not included), the EagleEyes constantly picks the better signal. This can greatly reduce video fades and improve your video image. A variety of settings are configurable with the on-board switches and LED indicators., Channel A/V Distribution:, Ever wish you had more video/audio outputs? The EagleEyes has four built-in outputs!, Programmable Low Voltage Alarm:, A low voltage alarm buzzer alerts you when your ground station battery voltage is too low. The buzzer can also be programmed to alert for other conditions, such as poor telemetry signal., Convenient Voltage Requirements:, EagleEyes operates on 6-14VDC (compatible with 3S LiPO batteries). The power inlet is a standard 2.1mm barrel jack. It is capable of powering high torque R/C type pan and tilt servos.,
The EagleEyes® FPV Ground Station combines antenna auto-tracking, receiver diversity, ...DPCAV
GUARDIAN 2D/3D INERTIAL STABILIZER (STANDALONE MODEL)
| Instruction Manual | Click Me! |
| PC Software | Click Me! |
Q: Why do I need the Guardian?, The Guardian helps both beginner and expert pilots fly with confidence, and provides two key modes of operation: In 2D flight mode, the Guardian provides much smoother flight and wing leveling stabilization for your model, which makes it a lot easier to adjust and fly your plane. The Guardian "remembers" level flight for your model and returns it to level flight when needed, as well as providing precise "fly by wire" control., The Guardian has two submodes for 3D flying: In 3D Heading Lock submode, simply center your sticks to have the Guardian lock onto your present attitude (pitch, roll, and heading), which can make it easier to perform stunts like prop hanging, inverted flight, knife edges, low speed harriers, etc. In 3D Gyro submode, the Guardian uses its built-in 3 axis gyro to increase your model’s stability, while leaving you in full control. In this mode the Guardian greatly reduces the effects of gusts, turbulence, motor torque and other factors, and can expand the maneuverability of your model in a variety of conditions., Q: I Fly FPV. Is the Guardian for me?, Q: Will the Guardian work with my model?, Q: How do I install the Guardian?, Q: How do I configure the Guardian?, Q: How does the Guardian work?, Q: What sets the Guardian apart from other Stabilization systems out there?, *Note: Using the PC software will require a common Micro-USB cable. Most likely you already have one of these, but it not then they are available from your local electronic/computer store.,
Based on Eagle Tree's proven inertial stabilization technology, the Guardian ...DPCAV
ELOGGER GPS-V4 EXPANDER MODULE (10-HZ)
| • Update Rate | 10Hz |
| • Time to Fix | 1 second hot, 36 second cold (typical) |
| • Sensitivity | approx -165dBm. |
| • Datum | WGS84. |
| • Current draw | 40 mA |
| Instruction Manual | Click Me! |
Note: When using the GPS Expander on your eLogger with 30VDC or higher voltages, the optional Battery Backup Cable, Update: We are now shipping the latest version with integrated EMI/RFI Toroid filter and longer cable. The filter reduces GPS signal interference problems caused by some wireless video transmitters. Please see photo on the right., GPS Expander Specifications:,
The Eagle Tree GPS-V4 Expander Module plugs into the eLogger ...DPCAV
9 GRAM R/C HOBBY SERVO
| Note | Servo styles, colors, and arm hardware may vary. |
| Supply voltage | 4.8V - 6V |
| Speed | 0.12sec, Torque |
| Cable length | 125mm |
| Dimensions (L x W x H) | Approximately 23 x 27 x 11 mm (may vary slightly). |
| Weight | ~9 grams, not including cable. |
General Specs:, ,
Generic (OEM) brand mini sized R/C hobby servo. It is ...DPCAV
E-SKY SERVO ADJUSTER / TESTER
Features:,
The E-Sky Servo Tester is a low cost servo signal ...DPCAV
DIGITAL OSCILLOSCOPE, 2-CHANNEL / 10MHZ (PORTABLE)
| Analog Bandwidth | 0 - 10MHz |
| Sensitivity | 10mV/Div - 2V/Div |
| Resolution | 8-bit |
| Input Impedance | 1M ohm |
| Maximum Input voltage | 50Vpk (for 1X probe) and 400Vpk (for 10X probe) |
| Coupling | DC, AC, GND |
| Max Real-time Sampling Rate | 50MSps |
| Timebase | 0.2us/Div - 10 minutes/div |
| Record Length | 500 - 8000 points (each channel) |
| Run/Hold Modes | one button switchable |
| Trigger Modes | Auto, Normal, Single |
| Trigger Types | Rising/falling edge |
| Trigger Sources | Ch 1 or Ch 2 |
| Trigger Position | 0 - 100% of capture buffer |
| Supply Current | 300mA @ 3.7V(LCD backlight ON, typical). |
| Dimension | 140mm X 70mm X 30mm |
| Weight | 190 gram (including battery) |
| Documents, firmware, and tools | Users Manual |
Portable 2-Channel 10MHz Digital Oscilloscope:, This portable scope offers a lot of features at an affordable price. It has 2-channels with 10MHz analog bandwidth (50msps) and it includes a rechargeable battery pack. Two switchable 10X scope probes are provided too!, The DSO-094 has useful features that are not commonly found in other low cost oscilloscopes. For example: It can be placed in "Persistent Display" mode that keeps waveforms on screen until you erase them; This is very useful when combined with NORMAL trigger mode to capture and compare multiple waveforms that meet your trigger conditions., Features:, , Specifications:, , Number of Channels: 2,
This is a FACTORY ASSEMBLED scope; It is not a ...DPCAV
DIGITAL OSCILLOSCOPE, 5MHZ (PORTABLE)
| Source Coupling | DC / AC / GND. |
| Storage Mode | Hold/run, BMP export. |
| Instruction Manual | Click Me! |
| Manufacture's Web Site | Click Me! |
Portable 5MHz Digital Oscilloscope:, It is hard to find a portable scope at this price with all these features. It has 5MHz bandwidth, FFT frequency domain display, a 20MHz frequency counter, and rechargeable battery pack. To make it a sweeter deal, you get a switchable 10X scope probe too!, Features:, Max Real Time sample rate - 2MSPS，8 bits., Useful Links:,
This is a FACTORY ASSEMBLED scope; It is not a ...